Meters to Roman Paces (m to passus)
1 meter equals 0.6756756757 Roman paces (rounded).
How to convert meters to Roman paces
To convert meters to Roman paces, multiply the number of meters by 0.6756756757. The factor is rounded to 10 significant digits. To go the other way, multiply Roman paces by 1.48.
Roman paces = meters × 0.6756756757
Example: 10 meters = 6.756756757 Roman paces.
Approximate value. Standards for the Roman pace varied by place and period, so this converter uses the most commonly cited value. Treat results as estimates, not exact figures.
About these units
Meter (m)
The SI base unit of length. Since 1983 it is defined as the distance light travels in a vacuum in 1/299,792,458 of a second.
Meter comes from the Greek metron, a measure. In 1791 the French National Assembly defined it as one ten-millionth of the distance from the equator to the North Pole along a great circle through Paris, after rejecting the length of a seconds pendulum because that length changes with local gravity. The surveyors Delambre and Méchain measured the meridian arc, and in 1799 a platinum bar known as the Mètre des Archives became the physical standard. NIST notes that this Earth-based meter turned out to be about 0.2 mm shorter than the true pole-to-equator fraction it was meant to represent.
The 1875 Treaty of the Meter created the CGPM and the BIPM to look after common standards, and in 1889 a platinum-iridium prototype bar took over; the original is still kept at the BIPM. In 1960 the meter was tied to 1,650,763.73 wavelengths of an orange-red krypton-86 line, and in 1983 to the speed of light, which made length a quantity derived from the time standard. The 2018 revision reworded that definition without changing the meter's size. NIST offers a handy yardstick for scale: a pace, meaning two steps, is roughly a meter or a yard.
The meter is the reference unit for length on this site.
Sources: BIPM: history of the metre; NIST: the meter and the SI redefinition; Wikipedia: Metre
Roman Pace (passus)
Five Roman feet, about 1.48 m. A passus was a full stride, from the lift of one foot to the same foot landing again.
Counting a pace by both feet is the key to the Roman passus. Unlike a single step, it ran from the point where one heel leaves the ground to where that same heel lands again, so it covered two steps, each called a gradus. Marcus Vipsanius Agrippa is credited with fixing it at five Roman feet, which comes to about 1.48 m, the figure used here. The exact size depends on the foot, whose surviving measures vary by a few millimeters.
A thousand paces, mille passus, formed the Roman mile of about 1.48 km, and the English word mile descends from that phrase. Milestones along roads such as the Appian Way marked distances in this unit,. The pace also sat in a chain of units: ten feet made a decempeda, and 120 feet made an actus. In imperial terms the passus is a little under five feet.
1 Roman pace = 1.48 meters (approximately).
Sources: Wikipedia: Pace (unit); Wikipedia: Ancient Roman units of measurement
Related conversions
- Roman paces to meters (reverse)
- Meters to kilometers
- Meters to centimeters
- Meters to millimeters
- Meters to inches
- Meters to feet
- Meters to yards
- Meters to miles
- Meters to micrometers
- Meters to nanometers
- Meters to nautical miles
- Meters to pixels (CSS)
- Meters to light-years
- Kilometers to Roman paces
- Centimeters to Roman paces
- Millimeters to Roman paces
- Inches to Roman paces
- Feet to Roman paces
- Yards to Roman paces
- Miles to Roman paces
See all length units.